The two additional deep NIR wavelengths go further than standard panels. 960nm enhances blood circulation and muscle recovery; 1060nm penetrates to the fat layer for body contouring support and deep chronic pain relief.

Connect via the Red Light Therapy app. Adjust each of the 7 wavelengths individually between 0–100% intensity, select a preset mode, set a timer, and save custom treatment configurations.

Choose a wellness goal and the app configures the optimal wavelength mix, intensity, and pulse frequency automatically — no manual setup needed.

Set the light to pulse at specific frequencies for targeted benefits — from mood support and cognition to wound healing and inflammation reduction.

Connect and control multiple X1500 Pro panels simultaneously from the app. No network cable required — ideal for clinic or multi-panel home setups.

Set your session time in 1-minute increments. The panel auto-shuts off when the timer ends, so there's no need to watch the clock.

Select from 12 goal-based modes. The app sets the ideal wavelengths, intensity, and pulse for your chosen treatment automatically.

Adjust each of the 7 wavelengths individually (0–100%). Save your preferred combination as a personal preset for quick access next time.

Choose any duration up to 30 minutes in 1-minute steps. The panel auto-shuts off at the end of the session.

Enable pulse mode and select from preset frequencies (10, 40, 73, 146, 293, 584 Hz) or enter any value from 1–999 Hz.

Mood support and burn wound recovery assistance

Cognitive support and short-term mental synchrony

Muscle spasm, facial tension, and headache relief

Memory, mental clarity, and stress reduction

Wound healing and skin and nerve repair

Cellular regeneration, nutrient absorption, inflammation reduction

~212 mW/cm² — Specific joints or muscles. 3–5 minutes max per area.

~187 mW/cm² — Ideal for most sessions. 5–15 minutes per area.

~170 mW/cm² — Broad coverage. 10–20 minutes total.

Daily or 5–6× per week. One rest day minimum. Noticeable results after 2–4 weeks of consistent use.

Toggles the red light (630nm + 660nm) on or off. Use red light for skin-level benefits: collagen support, surface healing, and complexion improvement.

Toggles the near-infrared light (810nm + 830nm + 850nm) on or off. NIR penetrates deeper — supporting muscle recovery, joint comfort, and inflammation reduction.

Increase or decrease your session timer in 1-minute increments. The panel will automatically switch off when the timer reaches zero.

Press both RED and NIR to run all five wavelengths simultaneously. This is the most commonly used mode for full-body wellness sessions.

Highest irradiance — for specific joints, wounds, or targeted muscle groups. Limit sessions to 3–5 minutes at this distance.

Ideal for most sessions. Covers a focused area with strong irradiance. Recommended for 5–15 minutes per treatment area.

Covers a broader body area at a comfortable distance. Best for 10–20 minute whole-body sessions.

Daily or 5–6 times per week. Include at least one rest day per week. Most people notice results after 2–4 weeks of consistent use.

The shallowest-penetrating wavelength, working primarily in the epidermis and upper dermis. Targets surface skin texture, fine lines, tone, and complexion. Stimulates collagen synthesis and supports the skin's natural renewal processes.

The most widely studied red light wavelength. Penetrates into the dermis to stimulate cellular energy production (ATP), support collagen, improve circulation, and accelerate tissue repair. The cornerstone of skin and wound healing protocols.

Crosses the boundary into near-infrared — invisible to the eye but deeply felt. Supports neurological function, cognitive clarity, mood, and brain health, while also assisting muscle recovery and anti-inflammatory responses.

Penetrates through dermal layers with strong tissue compatibility. Supports recovery processes, helps manage the microbial environment, and promotes bone recovery and growth.

The deepest-penetrating wavelength in this panel — reaching through soft tissue, muscle, and bone. Targets deep tissue recovery, physical stress response, post-activity recovery, and musculoskeletal comfort enhancement.

900W across 180 diodes delivers powerful whole-body photobiomodulation. Ideal for post-exercise recovery, reducing systemic inflammation, and supporting overall physical resilience.

Five wavelengths targeting multiple skin layers support texture improvement, tone evening, reduced visible lines, and a healthier complexion — from surface to deep dermis.

Deep NIR wavelengths reduce inflammation and relieve joint pain, muscle soreness, and stiffness — effective for both localised and full-body treatment.

Supports faster recovery from exercise and physical activity — reducing fatigue, swelling, and soreness at a cellular level, and preparing muscles for the next session.

Stimulates improved blood flow and ATP (cellular energy) production, supporting tissue repair, vitality, and whole-body wellness.

Evening sessions may promote relaxation and improve sleep quality through hormonal and neurological effects. Morning use can support energy and circadian alignment.

Toggles the red light channels on or off — activating the 630nm and 660nm LEDs. Use for skin-focused sessions, or combine with NIR for a full-spectrum treatment.

Toggles the near-infrared channels on or off — activating the 810nm, 830nm, and 850nm LEDs. Use alone for deep tissue and recovery-focused sessions.

Increases the session timer in set increments. The timer will count down and automatically switch off the panel when the session ends — no manual intervention needed.

Decreases the session timer. Use to shorten a session or fine-tune your treatment duration.

For skin and surface treatment, position 4–6 inches (10–15cm) from the panel. For full-body or systemic sessions, 12–24 inches (30–60cm) is recommended. The irradiance at 6 inches exceeds 187mW/cm².

Begin with 5–10 minute sessions and gradually increase to 10–20 minutes per session as your body adjusts. Most users do 1–2 sessions per day. Do not exceed 20 minutes on any single body area per session.

For skin health: RED only. For deep recovery and pain relief: NIR only. For comprehensive full-body treatment: RED + NIR combined. You can switch freely between these modes using the remote.

Morning sessions may boost energy and focus. Evening sessions (NIR-dominant) may support relaxation and sleep. Avoid intense red light sessions within 1 hour of bedtime.

Works with skin cells and sebaceous glands to improve skin texture, even pigmentation, reduce visible lines, support hair vitality, and promote a clearer complexion. Effective for surface-level skin concerns.

Penetrates deeper than 630nm into the dermal layer to support natural recovery processes. Reduces post-activity fatigue, manages post-injury swelling, and supports healthy skin appearance restoration.

Enhanced tissue penetration for post-procedure recovery, injury recovery support, head trauma response, skin repair, and hair follicle stimulation. Invisible to the naked eye but deeply active.

Penetrates through dermal layers with strong tissue compatibility. Supports recovery processes, helps manage the microbial environment, and promotes bone recovery and growth.

The deepest-penetrating wavelength in this panel — through soft tissue, muscle, and bone. Targets deep tissue recovery, physical stress response, post-activity recovery, and musculoskeletal comfort enhancement.

Five wavelengths targeting multiple skin layers support texture improvement, tone evening, reduced visible lines, and a healthier complexion.

Deep NIR wavelengths reduce inflammation and relieve joint pain, muscle soreness, and stiffness — particularly effective for localised treatment of specific problem areas.

Supports faster recovery from exercise, sport, and physical activity — reducing fatigue, swelling, and soreness at a cellular level.

Stimulates improved blood flow to treated areas, supporting tissue repair and overall vitality.

Evening sessions may promote relaxation and improve sleep quality. Morning use can support energy and circadian rhythm.

The compact tabletop design makes the X300-2 ideal for focused use on the face, neck, hands, knees, or any specific area — simply place it on a flat surface and direct it where needed.

Toggles red light (630nm + 660nm) on or off. Use for skin-level benefits — texture, tone, collagen support, and surface recovery.

Toggles near-infrared light (810nm + 830nm + 850nm) on or off. Use for deep tissue, joint, muscle, and bone benefits.

Increases the session timer. Both light types can be run simultaneously — simply activate RED and NIR together for full 5-wavelength therapy.

Decreases the session timer. The panel will switch off automatically when the timer reaches zero.

Irradiance: ~212 mW/cm² · Coverage: ~42×18 inches. Highest intensity for targeted localised treatment. Limit to 5 minutes per area at this distance.

Irradiance: ~187 mW/cm² · Coverage: ~45×21 inches. Ideal balance of intensity and coverage. Recommended for 5–15 minute targeted sessions.

Irradiance: ~170 mW/cm² · Coverage: ~49×25 inches. Good for systemic or whole-area sessions. Recommended for 10–20 minutes of total exposure.

Daily or near-daily sessions yield the best results. Keep total daily exposure to 20–25 minutes maximum. Allow at least one rest day per week for optimal cellular recovery.

Operating in the 600–700nm range, red light works at the surface and upper dermal layers. It stimulates collagen production, improves skin texture and tone, smooths fine lines and wrinkles, and supports general skin and hair rejuvenation. It is the primary wavelength for skin-focused treatments.

Invisible to the eye but deeply penetrating, NIR at 850nm reaches into muscle, connective tissue, and joints. It assists with wound healing, accelerates muscle recovery, supports nerve repair, and relieves joint pain and stiffness — making it the key wavelength for physical recovery and deep tissue therapy.

NIR penetrates deep into joint tissue to reduce inflammation and improve mobility. Particularly effective for knees, elbows, wrists, ankles, and the lower back when wrapped directly around the affected area.

Supports faster recovery after exercise or physical activity by reducing soreness, inflammation, and fatigue at a cellular level. Wrap around the affected muscle group post-workout for best results.

660nm red light stimulates collagen, improves skin tone and texture, and reduces visible fine lines — effective for targeted skin treatment on the face, neck, hands, or décolletage.

Combined red and NIR wavelengths accelerate tissue repair and reduce inflammation around injuries, supporting faster natural healing of soft tissue.

NIR therapy supports nerve repair and improved local circulation, helping with numbness, tingling, or restricted blood flow in targeted areas.

Its compact, wearable form means it can be used anywhere — at home, at the office, or travelling. Wrap it around any body part for quick daily maintenance sessions.

1 session per day. Suitable for general skin maintenance, light muscle soreness, or preventative use. Each session lasts up to 20 minutes — the device auto-shuts off at this point.

2 sessions per day. Recommended for ongoing joint pain, moderate muscle recovery, or skin concerns that require more consistent treatment. Allow at least 2 hours between sessions.

Up to 3 sessions per day. For persistent pain, injury recovery, or serious skin conditions. Consult your healthcare provider before beginning an intensive protocol.

Most users begin to notice improvement between 6 and 24 weeks of consistent use. Skin results typically appear earlier (4–8 weeks); deeper tissue benefits such as joint pain relief may take longer.

Align the Type-C cable with the charging port on the back of the device and connect to a USB power source (wall adapter or computer). Ensure the device is turned off before charging.

Red light flashing = currently charging. Green light flashing = battery is low (charge needed). Once charging is complete, the indicator will stop flashing.

Do not use the device while it is charging. Keep the device and charging cable away from water at all times. Store unplugged in a cool, dry location between sessions.

The device automatically shuts off after 20 minutes of continuous use to prevent overuse and protect the LEDs. To end a session early, press the button briefly.

660nm red light targets the dermal layers of the skin to support natural recovery processes. It helps reduce post-activity fatigue, manage post-injury swelling, and support the recovery of healthy skin appearance. When you power on the mat, red light is active immediately alongside NIR.

At 850nm, near-infrared light penetrates well beyond the skin surface — through soft tissue, muscles, and even bone — to support deep tissue recovery, reduce physical stress response, and enhance musculoskeletal comfort. The 850nm wavelength is invisible to the naked eye; if the mat appears to emit only red light, both wavelengths are still active.

Supports improved blood circulation, enhanced tissue repair, and faster muscle recovery after sport or exercise.

Helps relieve joint pain and stiffness, and can aid bone recovery as NIR light penetrates to deeper skeletal structures.

Reduces inflammation and relaxes sore, tight muscles — particularly useful for athletes and those with chronic tension.

Supports improvement in skin texture, stimulates circulation at acupuncture points, and can assist with overall foot and ankle health when the mat is used underfoot.

Evening sessions may promote relaxation and improve sleep quality. Morning sessions can help energise and support your circadian rhythm.

At 1855×830mm, the mat is large enough for full-body lie-down sessions, covering the back, legs, and feet simultaneously.

Press to turn the mat on or off. When powered on, both 660nm red and 850nm near-infrared LEDs activate simultaneously.

Press the + or – brightness buttons to cycle through five power levels. P1 is the lowest intensity; P5 is maximum. Start at P1–P2 if you are new to red light therapy.

Press Timer+ or Timer– to set your session length in 10-minute increments: 10, 20, 30, 40, 50, 60, 70, 80, or 90 minutes. The mat will switch off automatically when the timer ends.

Press the pulse button to activate pulse mode. First press activates 10Hz; second press activates 40Hz; third press returns to steady (continuous) light. 10Hz is associated with mood and tissue repair; 40Hz with cognitive support.

30 minutes per session is the standard recommendation. Sessions up to 90 minutes are supported by the timer, but avoid exceeding 30 minutes daily as a consistent practice to prevent diminishing returns.

Daily or near-daily sessions yield the best results. Include at least one rest day per week to allow optimal tissue recovery and cellular adaptation.

Initial improvements are often noticeable after 2–4 weeks of regular use. Subtle changes like better sleep quality may appear sooner. Consistency is essential for lasting results.

Morning sessions can help energise the body and support circadian rhythm. Evening sessions may promote relaxation and improve sleep quality. Choose whichever fits your routine.

The RS 2576 has an upper and a lower panel. You lie on the lower panel and the upper panel closes over you — buckle fastenings secure the bag around your body so both sides receive light simultaneously.

With 2,576 LEDs across both panels (vs 1,328 on the Sports Mat), light reaches your back, sides, chest, and front at the same time — no need to flip over or reposition mid-session.

Each panel has its own controller and power supply, allowing you to run both panels simultaneously, adjust their brightness levels independently, or use just one panel at a time.

At 190W combined (two 95W panels), the RS 2576 delivers double the irradiance coverage of the Sports Mat — maximising therapeutic dose across the largest possible body surface area.

660nm red light targets the dermal layers to support natural recovery processes — reducing post-activity fatigue, managing post-injury swelling, and supporting healthy skin appearance. Visible as the warm red glow from both panels.

850nm NIR light penetrates beyond the skin into muscles, organs, and bone to support deep tissue recovery, reduce the physical stress response, and enhance musculoskeletal comfort. Invisible to the naked eye but active whenever the bag is on.

Simultaneous front and back coverage makes the RS 2576 ideal for full-body post-exercise recovery — muscles, joints, and connective tissue across the entire body receive light in one session.

Supports improved blood circulation and reduced inflammation throughout the body, rather than in a localised area.

Deep NIR penetration aids bone recovery and helps relieve joint pain and stiffness from all sides simultaneously.

Enhances tissue repair and improvement in skin texture across a large body surface area in a single session.

Evening sessions enclosed in the bag create a deeply relaxing environment and may significantly improve sleep quality. One of the most popular use cases for this product.

Morning sessions can help energise the body and support a healthy circadian rhythm for the day ahead.

Press to turn the panel on or off. When powered on, both 660nm red and 850nm NIR LEDs activate simultaneously on that panel.

Press + or – to adjust brightness across five levels. P1 is lowest; P5 is maximum. Start at P1–P2 if you are new to red light therapy or sensitive skin.

Set session length in 10-minute increments: 10, 20, 30, 40, 50, 60, 70, 80, or 90 minutes. Each panel auto-shuts off when its timer ends.

Press the pulse button to activate: first press = 10Hz, second press = 40Hz, third press = steady light. 10Hz supports mood and tissue repair; 40Hz supports cognitive function.

30 minutes per session is the standard recommendation. The timer supports up to 90 minutes, but keep daily exposure to around 30 minutes maximum to avoid diminishing returns or skin sensitivity.

Daily or near-daily sessions yield the best results. Include at least one rest day per week to allow optimal cellular recovery and adaptation.

Initial improvements are often noticeable after 2–4 weeks of regular use. Sleep quality improvements can appear sooner. Consistency over weeks and months yields the most lasting results.

Evening sessions enclosed in the bag are particularly effective for promoting deep relaxation and improving sleep quality. Morning use can energise and support circadian rhythm.

Red light at 630nm promotes collagen production, tightens and firms the skin, and supports anti-ageing effects. It works at the surface and mid-dermal layer to improve skin elasticity and overall texture over time.

Blue light at 460nm targets acne-causing bacteria on the skin surface, reducing active breakouts, calming inflammation, minimising scarring, and improving overall skin clarity and glow. It is the most commonly used mode for oily or congested skin.

Yellow light at 590nm balances skin texture and tone, stimulates red blood cell activity to reduce facial redness, and softens fine lines. Particularly helpful for those with sensitive or uneven skin tone, rosacea, or persistent flushing.

Near-infrared at 850nm penetrates beneath the skin surface to support deeper tissue repair, improve circulation, and boost skin moisture levels. Invisible to the eye but independently active — it can be combined with any of the three visible light modes.

Long-press for 1–2 seconds to turn the mask on or off. A short press cycles through the four light modes: Red → Blue → Yellow → Near-Infrared → combined modes.

Short-press to cycle through 3 intensity levels for the current light mode. Level 1 is lowest (good for new users); Level 3 is full power. Each mode has its own independent intensity setting.

Increases session time. Available settings: 10 / 15 / 20 / 25 / 30 minutes. The mask will automatically shut off when the timer ends.

Decreases the session time in the same increments. Set your timer before beginning — 15–25 minutes is the recommended single-session duration.

15–25 minutes per session. Do not exceed 30 minutes in a single session.

3–4 times per week is recommended for consistent results. Allow recovery days between sessions.

Start with Level 1 intensity and a 15-minute timer for your first few sessions. Once comfortable, gradually increase to Level 2 or 3 and extend to 20–25 minutes.

Near-infrared (850nm) can be used simultaneously with any visible light mode for enhanced results. For example, Red + NIR is popular for anti-ageing sessions; Blue + NIR for acne treatment.

Promotes collagen formation and improves skin elasticity. Supports whitening, rejuvenation, tightening, and the repair of damaged skin. Reduces pores and helps reverse the visible signs of ageing over consistent use.

Delivers bactericidal and anti-inflammatory action. Targets acne-causing bacteria, reduces active breakouts and sores, sterilises the skin surface, and reduces post-acne pigmentation — without leaving scars or harsh side effects.

Reduces excess skin oil secretion, balances the complexion, and calms stress-related skin responses. Supports lymphatic drainage and reduces facial puffiness and swelling.

Replenishes cellular energy and decomposes pigmentation. Promotes lymphatic drainage, smooths skin roughness, reduces redness and fine lines, and addresses conditions such as ringworm and fever-related skin responses. Enhances overall skin immunity.

A dual-frequency combination of red and blue light, targeting both acne bacteria and skin repair simultaneously. Particularly effective on post-acne scarring and blemish-prone skin. Produces a synergistic repairing and renewing effect.

Increases cellular energy step by step and supports overall skin metabolism. A gentle, balanced mode that complements other targeted wavelengths during combined or transitional treatment sessions.

Penetrates deep into skin layers to accelerate skin metabolism, break down pigment spots, improve fine lines, and address sagging. The broadest-acting mode, suitable for general skin renewal and maintenance.

Near-infrared at 850nm penetrates beneath the visible skin surface to accelerate skin metabolism at a cellular level, break down pigmentation, and improve fine lines and skin laxity. Invisible to the eye but independently active.

15–30 minutes per session. 15–30 minutes is ideal; do not exceed 30 minutes in a single sitting.

Begin with a shorter session (15 minutes) at a lower intensity. As your skin acclimatises over the first week, you can extend session duration and gradually increase the intensity level.

For acne-prone skin: start with Blue or Purple. For anti-ageing and firming: use Red or White. For pigmentation: Yellow or White. For overall maintenance: cycle through multiple modes across different sessions.

Always wear the included goggles or keep eyes firmly closed throughout every session. Do not stare at the light source — even brief direct exposure should be avoided.

After each session, wipe the silicone surface with a soft damp cloth. Do not submerge in water, place under running water, or use abrasive cleaning products.

The elastic straps can be cleaned with water. Allow to air dry fully before re-attaching to the device.

Store the device in the original gift box when not in use. Avoid prolonged exposure to direct sunlight during storage. Keep out of reach of children.

Do not use corrosive chemical solvents to clean any component. Do not expose the device to sunlight for extended periods. Do not use if any part of the device appears damaged or cracked.

Targets the dermis to stimulate collagen production, improve skin texture, reduce fine lines, and boost circulation. The most widely used wavelength for anti-ageing and skin rejuvenation protocols.

Operates at the surface of the skin to target acne-causing bacteria (P. acnes). Helps reduce breakouts, control oiliness, calm inflammation, and improve overall skin clarity and redness.

Penetrates deeper than visible light — supporting cellular energy production, accelerating tissue repair, reducing inflammation below the surface, and enhancing the effects of the red and blue channels when combined.

Red + Near Infrared Light (630nm + 850nm)
Reduces wrinkles and fine lines, boosts circulation, and promotes skin radiance. Ideal for anti-ageing, glow enhancement, and general skin rejuvenation. Use for up to 10 minutes at high brightness, 4 times per week.

Blue + Near Infrared Light (460nm + 850nm)
Targets acne-causing bacteria, reduces inflammation and redness, and improves overall skin clarity. Use for up to 10 minutes at high brightness, 4 times per week.

Red + Blue + Near Infrared Light (630nm + 460nm + 850nm)
Full-spectrum treatment combining all three wavelengths for deep skin penetration — reduces wrinkles and fine lines, brightens skin, and addresses multiple concerns simultaneously. Use for 10-minute sessions up to 4 times per week, or 5-minute sessions up to 3 times per week.

Red and NIR wavelengths stimulate collagen synthesis and support cellular repair, visibly reducing lines and improving skin firmness over consistent use.

Blue light targets P. acnes bacteria at the surface, reducing active breakouts and helping prevent new ones. Combined with NIR, it also calms inflammation and redness.

Multi-wavelength treatment improves overall skin tone, minimises pores, and reduces hyperpigmentation and uneven texture for a more even, brighter complexion.

Red light stimulates blood flow in the facial tissue, supporting nutrient delivery and giving skin a natural, healthy radiance after sessions.

NIR wavelengths reduce inflammation at a cellular level, complementing blue light's antibacterial effects to calm reactive and sensitive skin types.

Mode 3's full-spectrum approach — all three wavelengths simultaneously — targets multiple skin layers and concerns in a single session for maximum overall benefit.

Press and hold the power button for 3 seconds to turn the mask on or off. Do not short-press — this avoids accidental activation.

Press the M button on the remote to cycle through the three therapy modes: M1 (Glow Boost) → M2 (Clear Skin) → M3 (Deep Rejuvenation). The current mode will be indicated on the controller.

Three brightness settings are available — Low, Medium, and High. For best results in all modes, use the mask on High brightness. Sensitive skin users should start at Low or Medium and increase gradually.

Three timer presets: T1 (5–10 min), T2 (5–10 min), T3 (10–15 min). When using the mask for the first time, start with T1 set to 5 minutes as a test session. Increase duration gradually as your skin adjusts.

Recommended: Up to 10 minutes per session at high brightness. Frequency: 4 times per week.

Recommended: Up to 5–10 minutes per session at high brightness. Frequency: 4 times per week.

Recommended: 10-minute sessions at high brightness. Frequency: Up to 4 times per week.

Recommended: 5-minute sessions for higher-intensity use. Frequency: Limit to 3 times per week.

Connect the USB-C cable to the charging port on the controller. Plug the other end into a USB power source (wall adapter or computer). The indicator light will flash during charging and remain solid when complete.

Red indicator light = Charging. Green indicator light = Fully charged. When the battery is low, the indicator on top of the mask will turn red — charge before your next session.

Full charge takes approximately 3 hours. The 1440mAh battery provides up to 40 minutes of use — enough for 4 ten-minute sessions, 5 eight-minute sessions, or 3 longer sessions per charge.

The mask cannot be used while charging. Always disconnect the USB cable before putting the mask on for a session. Charge in a safe location away from water.

Red light at 660nm accelerates cellular metabolism, promoting healthier skin on the scalp, speeding up healing, and supporting hair regrowth. It works at the surface and dermal layer where hair follicles are found.

At 850nm, near-infrared light penetrates beyond the skin into the scalp tissue, joints, and underlying structures. It helps reduce inflammation, enhance circulation, ease tension headaches, and further support hair regrowth. Note: 850nm light is invisible to the naked eye — the panel may appear to emit only red light, but both wavelengths are active.

Turns the cap on at its lowest brightness setting. A good starting point for new users or shorter sessions.

Increases brightness to the mid-level intensity. Suitable for most regular sessions.

Maximum brightness — full LED output. Use for intensive sessions once your body has adapted to the therapy.

Hold the button to turn the cap off at any point during a session.

The LEDs gradually fade in and out in a slow breathing rhythm. A gentle, calming mode suitable for relaxation and winding down before sleep.

The LEDs pulse at 10 times per second. Research associates 10Hz with mood support and tissue repair benefits.

The LEDs pulse at 40 times per second. The 40Hz frequency is associated with cognitive support and neural activity stimulation.

Start with just 2 minutes at Level 1. Gradually increase by a minute or two each session over 2 weeks until you reach a comfortable 10–20 minute routine.

20 minutes per session, 3–4 times per week is the recommended routine for consistent results.

Some people notice improvements within days. For hair regrowth and deeper health benefits, allow 8–12 weeks of consistent use to assess results.

The cap turns off automatically after 30 minutes — no need to watch a timer. Simply put it on, press start, and relax.

Store the cap flat — do not fold or bend it. Folding the cap may damage the internal LED components. Keep it in its original packaging or a flat surface when not in use.

Turn off and unplug the charger before any cleaning. Wipe the outer surface gently with a dry or slightly damp cloth. Do not submerge in water or use harsh cleaning products.

Press to raise the panel. The digital display shows the current height in real time. Release when the panel reaches your desired treatment position.

Press to lower the panel. Use to bring the panel down for seated or floor-level treatment, or to store at a lower position between sessions.

Save up to three height positions for instant recall. To save: press "S" — the indicator shows "S-" and flickers — then press 1, 2, or 3 to store the current height to that position. Press the same number again to recall it instantly.

Used to activate memory saving mode and for unit conversion. Hold "S" for 8 seconds to toggle between centimetres and inches on the display.

Shows the current height of the panel in real time as the stand moves. Both the wired controller and remote display the same reading.

To pair the remote: hold "S + ↓" simultaneously until the remote display shows "00.0". While the stand is powered on, the remote display will then show "Co" — this confirms successful pairing.

If the hand controller displays "RST", the stand needs to be reset. Press and hold the Down (↓) button for 10 seconds until the digital display shows a height number. The stand is now reset and ready for normal use.

After 3–4 continuous operation cycles, the system enters protection mode. The handset will display "HOT" and both the remote and wired controller will stop responding. After 18 minutes, the stand will automatically reconnect — or you can power it off and back on to reset it immediately.

Hold the "S" button for 8 seconds. The height display unit will automatically switch between centimetres and inches. This setting is retained after power off.

The panel mounting bracket can be rotated 180° to switch your light panel between vertical orientation (portrait — for standing full-body treatment) and horizontal orientation (landscape — for targeting specific body zones). Always power off the stand before rotating the panel.

Always power off your panel before adjusting the stand height. Loosen the collar, reposition the post to the new height, then retighten firmly before powering the panel back on. Never adjust height while the panel is running.

Unlock all four casters before moving. Roll the stand gently on flat, smooth surfaces. Avoid rolling over cables, door thresholds, or uneven surfaces that could tip the stand. Re-lock all casters once the stand is in position.

Position yourself at your panel's recommended treatment distance (typically 6–24 inches depending on your panel model and session type). Adjust the stand height so the panel is centred on the body area being treated.

The stand can be stored with the panel attached if space allows. For compact storage, lower the post to its minimum height. The stand's packaging dimensions are 80 × 73 × 9cm — it can be broken down to those dimensions if needed.

PEMF sends electromagnetic waves through the body at adjustable frequencies (1–30Hz), promoting the body's natural recovery and healing processes. Scientifically proven to recharge cells, aid tissue healing, promote relaxation, and reduce stress. Four frequency bands — Delta, Theta, Alpha, and Beta — each produce distinct mental and physical effects.

Far infrared heat penetrates deep into the body's tissues — beyond what surface heat can reach. It dilates blood vessels to improve circulation, increases nitric oxide production to reduce inflammation, relieves chronic pain, promotes detoxification through sweating, stimulates collagen for skin health, and supports deeper, more restorative sleep.

The mat's built-in photon LEDs emit multi-colour light across the body surface, supporting cellular energy production, skin rejuvenation, and mood. Photon therapy complements the infrared and PEMF frequencies for a comprehensive full-body light and energy therapy experience.

When the mat's crystals are heated, they produce negative ions — the same naturally occurring ions found in forests, beaches, and after rain. Negative ions act like antioxidants in the air, neutralising free radicals and raising serotonin levels, which improves mood, mental clarity, and overall sense of wellbeing.

Promotes deep relaxation, enhances restorative sleep, and supports the body's regenerative and repair processes. Ideal for evening sessions, winding down, or recovery after illness or intense physical activity. May assist in reducing stress and promoting rejuvenation.

Induces a calm, meditative state — relaxation with mental clarity. Supports creative thinking, reduces anxiety, and promotes a sustained sense of calmness. Well suited to meditation, light rest, or creative work sessions.

Assists in promoting relaxation while supporting focus and concentration. Reduces stress and enhances mental clarity — ideal for achieving a mindful, present state. Good for daytime use when you need calm focus without drowsiness.

Increases mental alertness and cognitive function — supports productivity, memory, and overall mental acuity. Best used earlier in the day or before tasks that require sharp mental performance. Avoid close to bedtime.

Far infrared heat reduces inflammation and increases circulation, providing relief for chronic pain conditions including arthritis, muscle pain, joint stiffness, and back pain.

A single session on Delta or Theta settings provides grounding and relaxation equivalent to an hour of yoga or meditation — combined with the calming effects of negative ions and infrared warmth.

Far infrared heat and Delta PEMF frequencies relax the body and mind, reduce stress and anxiety, and make it easier to fall asleep and maintain deep, restorative sleep.

Infrared heat dilates blood vessels for improved circulation — supporting nutrient delivery, tissue repair, and post-exercise recovery throughout the whole body.

Far infrared-induced sweating promotes the elimination of toxins through the skin — one of the body's primary detox pathways. Regular sessions support systemic cleansing and skin clarity.

Alpha and Beta PEMF frequencies enhance focus, concentration, memory, and mental acuity — useful before work, study, or any task requiring sustained cognitive effort.

Before cleaning, turn off the controller and unplug from all power sources. Remove dust with a slightly damp cloth, a non-toxic cleaning wipe, or a handheld vacuum cleaner. Never use chemical solvents (such as benzene or thinner) on the controller pad.

Allow the mat to cool completely before folding. Fold in the correct manner and store inside the provided carrying bag. Store in a cool, dry place away from humidity, dust, and oiliness. Do not place heavy objects on top of the stored mat.

Never place the mat or its controller in a washing machine. The mat is not washable — surface cleaning only with a damp cloth or non-toxic wipe.

Do not iron the product. Unplug and store in a cool, dry place between sessions. Keep away from direct sunlight and high temperatures when not in use, as prolonged heat exposure can reduce lifespan.

The mat is warranted to function within specification for 1 year from the date of delivery. Any defects in material or workmanship under normal use will be repaired or replaced at no charge during this period.

The warranty does not cover damage caused by negligence, improper maintenance, unauthorised modification, natural causes (lightning, floods), theft, or loss of the product.